AEG Lavamat error codes
Match your aeg lavamat problem with error codes table, i hope it can be guide for the solution :If washing machine still have a problem, i suggest you for contact washing machine expert or just call local service center.
error code |
sub code |
AEG error code definition |
washing machine problem solution |
Solution through white goods engineer |
error code E10 |
E11
|
No water supply to washing machine |
water tap,
filter (screen) clean
|
Electronics
/ valve / connection cable / pressure switch / replace luchtval
|
E13
|
Too little water in washing machine |
Check
valve, supply hose and hose correctly explain (kink in the hose), filter
cleaning.
|
Valve /
inlet hose / pressure switch replaced / hydraulic control circuit.
|
|
error codeE20 |
E21
|
No drainage from the washing machine |
Filter
check for foreign objects, drain control, hose, tube blockage.
|
Pump /
pressure switch / pressure sensor / electronics replaced
|
E23
|
Pump / electronics washing machine problem |
Supplier
of bubble machine
|
Pump /
electronics / tire pump cables replaced
|
|
E24
|
Measuring
Circuit
|
Call
supplier
|
Replace
electronics
|
|
Error Codes E30 |
E31
|
Pressure washing machine problem |
Call
supplier
|
Pressure
sensors / flat cable replaced
|
E32
|
Pressure sensor gives a message |
Water tap,
filter check for objects.
|
Valve /
luchtval / pressure sensor replaced
|
|
E33
|
Pressure sensor problem |
Call
supplier
|
Pressure
switch / pressure sensor / tape / cable luchtval / heating / electronics
replaced
|
|
E34
|
Pressure sensor problem |
Call
supplier
|
Pressure
sensor / tape / cable replacement luchtval
|
|
E35
|
Safety message in washing machine |
Call
supplier
|
Pressure
switch / pressure sensor / tape / cable luchtval / electronics / replace
hydraulic control circuit.
|
|
E36
|
Measuring
circuit problem
|
Call
supplier
|
Replace
electronics
|
|
E37
|
Measuring
circuit problem
|
Call
supplier
|
Replace
electronics
|
|
E38
|
Pressure
switch problem
|
Call
supplier
|
Luchtval
cleaning / replacement
|
|
E39
|
Pressure
switch problem
|
Call
supplier
|
Replace
electronics
|
|
E3A
|
heater relay problem |
Call
supplier
|
Replace
electronics
|
|
error E40 |
E41
|
Open lid, locking machine malfunction. |
Lock
control, where defective: Call dealer
|
Locking /
link / cable replacement electronics
|
E42
|
Defective locks, open during wash / will not open at the end wash. |
Call
supplier
|
Locking /
link / cable replacement electronics
|
|
E43
|
Triac (power
circuit) locking of machine breakdown
|
Call
supplier
|
Locking /
link / cable replacement electronics
|
|
E44
|
Measuring
Circuit locking
|
Call
supplier
|
Replace
electronics
|
|
E45
|
Measuring
Circuit locking
|
Call
supplier
|
Replace
electronics
|
|
error codeE50 |
E51
|
motor triac (power
circuit) circuit
|
Call
supplier
|
Electronics
/ flat cable replaced
|
E52
|
Engine
failure blockade / tachometer (rotation meters) interruption / motor ribbon
cable defective.
|
Call
supplier
|
Tachometer
/ engine / tire / cable electronics replaced
|
|
E53
|
Measuring
Circuit engine
|
Call
supplier
|
Replace
electronics
|
|
E54
|
Engine
failure relay
|
Call
supplier
|
Replace
electronics
|
|
E55
|
Motor
circuit is interrupted
|
Call
supplier
|
Motor
replacement / flat cable check
|
|
E56
|
Adjournment
tachometer (rotation meters)
|
Call
supplier
|
Tachometer
replaced
|
|
E57
|
Total
current greater than 15A
|
Call
supplier
|
Engine /
engine electronics / flat cable replaced
|
|
E58
|
The flow
of a phase larger than 4.5 A
|
Call
supplier
|
Engine /
link / cable replacement engine electronics
|
|
E59
|
no
tachometer signal (rotation meters) to the engine
|
Call
supplier
|
Tachometer
/ engine / tire / cable electronics replaced
|
|
E5A
|
heatsink
temperature exceeds 88 degrees
|
Call
supplier
|
Engine
electronics module
|
|
E5B
|
Voltage
below 175 Volts
|
Call
supplier
|
Electronics
Engine / flat cable replaced
|
|
E5C
|
Voltage
exceeding 430 Volts
|
Call
supplier
|
Engine
electronics module
|
|
E5D
|
Data
transmission problem
|
Call
supplier
|
flat cable
replaced
|
|
E5e
|
Communication
error engine electronics
|
Call
supplier
|
Replace
electronics
|
|
E5F
|
Engine
Electronics fault
|
Call
supplier
|
Electronics
/ engine electronics / flat cable replaced
|
|
error code E60 |
E61
|
Does not
heat, heating or NTC defective.
|
Call
supplier
|
NTC /
heating / flat cable replaced
|
E62
|
Superheat
temperature exceeding 88 degrees
|
Call
supplier
|
NTC /
heating / flat cable replaced
|
|
E66
|
Heating
relay defective.
|
Call
supplier
|
Dry
running protection 1 / 2 dry run protection / link / cable replacement
electronics
|
|
E68
|
Excessive
flow diversion
|
Call
supplier
|
Heater or
other parts inside
|
|
E69
|
Does not
heat, voltage> 5Volt
|
Call
supplier
|
Heater /
flat cable replaced
|
|
error codeE70 |
E71
|
NTC (temperature
sensor) is defective.
|
Call
supplier
|
NTC / tape
/ cable electronics replaced
|
E74
|
NTC is
not the right place
|
Call
supplier
|
Mounting
position NTC control
|
|
error code E80 |
E82
|
Wrong
reste-position program switch
|
Call
supplier
|
Replace
electronics
|
E83
|
Read error
program switch
|
Call
supplier
|
Wrong
configuration, replace electronics
|
|
E84
|
Measuring
circuit circulation pump
|
Call
supplier
|
Replace
electronics
|
|
E85
|
Circulating
pump failure
|
Call
supplier
|
Circulation
Pump / electronics replaced
|
|
error codeE90 |
E91
|
Error in
communication electronics
|
Call
supplier
|
E / A
electronics / belt / cable electronics replaced
|
E92
|
Inequality
in electronics
|
Call
supplier
|
E / A
electronics fit to head electronics
|
|
E93
|
Incorrect
configuration
|
Call
supplier
|
Replace
electronics
|
|
E94
|
Incorrect
configuration wash
|
Call
supplier
|
Replace
electronics
|
|
E95
|
communication
error
|
Call
supplier
|
Replace
electronics
|
|
E96
|
no
consensus in hardware version of the configuration
|
Call
supplier
|
Replace
electronics
|
|
E97
|
no
consistent program and switch configuration
|
Call
supplier
|
Replace
electronics
|
|
E98
|
disagreement
engine electronics and other electronics
|
Call
supplier
|
Electronics
/ flat cable replaced
|
|
E99
|
in-/uitgave
electronics speaker problem
|
Call
supplier
|
Speaker /
flat cable replaced
|
|
E9A
|
Speaker
firmware problem.
|
Call
supplier
|
Import /
editing electronics replaced
|
|
E9F
|
communication
error between the engine electronics and other electronics
|
Call
supplier
|
Electronics
/ flat cable replaced
|
|
error codeEA0 |
Ea1
|
DSP
failure
|
Call
supplier
|
DSP / tire
cord / belt / electronics replaced
|
EA2
|
DSP
reports failure
|
Call
supplier
|
Replace
electronics
|
|
EA3
|
DSP engine
pulley can not block.
|
Call
supplier
|
DSP /
ribbon cable / electronics / belt replaced.
|
|
EA4
|
DPS defect
|
Call
supplier
|
DSP /
electronics / flat cable replaced
|
|
EA5
|
Triac DSP
failure
|
Call
supplier
|
Replace
electronics
|
|
EA6
|
Drum
blocked in 3 to 30 seconds
|
Call
supplier
|
DSP
replacement, belt replacement, drum lid has been opened.
|
|
error codeEB0 |
EB1
|
Frequency
outside limits
|
Voltage
power mains wrong / insane. If correct: call vendor
|
Replace
electronics
|
EB2
|
Mains
voltage too high
|
Voltage
mains socket faulty / degraded. If correct: call vendor
|
Replace
electronics
|
|
EB3
|
Mains
voltage too low
|
Voltage
mains socket faulty / degraded. If correct: call vendor
|
Replace
electronics
|
|
EBE
|
Defective
safety relay control panel
|
Call
supplier
|
Replace
electronics
|
|
EBF
|
Cycle
control circuit of the safety relay is defective.
|
Call
supplier
|
Replace
electronics
|
|
error code EC0 |
EC0
|
Valve
blocks
|
Call
supplier
|
Valve /
electronics / flat cable replaced
|
EC2
|
Dirt level
sensor malfunction
|
Call
supplier
|
Sensor
replaced
|
|
error
EF0
(EFO)
see top of this page! |
EF1
|
Screen
lint clogged, clogged afvoerdam
|
Lint
Screen / afvoerdam cleaning
|
-
|
EF2
|
Overdoses
foam during pumping, lint screen clogged, clogged afvoerdam
|
Not
overdosing on lint screen / cleaning afvoerdam
|
-
|
|
EF3
|
Aqua
Control system mobilized / ribbon cable defective pump / pump failure
|
Call
supplier
|
Leak in
appliance repair / replace connection cable / pump.
|
|
EF4
|
No signal
of flow sensor
|
encourage
water / water control.
|
Flow
Sensor blockade lifted.
|
|
EF5
|
Centrifugation
is interrupted, imbalance greater than 1200 grams
|
At large
loads watch / Placement of machine vibration and possible correction.
|
-
|
|
error code EH0 |
EH1
|
Frequency
outside the limit
|
Call
supplier
|
Valve /
electronics / flat cable replaced
|
EH2
|
Mains
voltage too high
|
Voltage
mains socket faulty / degraded. If correct: call vendor
|
Replace
electronics
|
|
EH3
|
Mains
voltage too low
|
Voltage
mains socket faulty / degraded. If correct: call vendor
|
Replace
electronics
|
|
EHE
|
Defective
safety relays on the steering wheel panel
|
Voltage
mains socket faulty / degraded. If correct: call vendor
|
Replace
electronics
|
|
EHF
|
Cycle
control circuit of the safety relay is defective.
|
Call
supplier
|
Replace
electronics
|
Taken from http://www.meolease.nl/AEG_wasmachine_foutcodes.htm and translated from Dutch.
Tag :
aeg lavamat vault,
error code